CRC NF Contact Cleaner - 400g
I. Product Description
CRC NF Contact Cleaner is a cutting-edge, stable, and non-flammable cleaning solvent with no flash point. It is formulated to be high-purity, non-conductive, non-corrosive, and residue-free. This cleaner ensures rapid evaporation and leaves no stains, making it ideal for sensitive electronic components.
Key Features:
- No Flash Point
- Non-flammable
- Fast Evaporation
- Residue-Free
- Contains no CFC 113 or Methyl Chloroform
II. Applications
CRC NF Contact Cleaner is highly recommended for cleaning a wide range of electronic and electrical components:
- Relays
- Switches
- Circuit Breakers
- Alarm and Signal Systems
- Printed Circuit Boards
- Connectors
- Generators
- Laboratory and Test Equipment
- Motor Controls
- Sensors
- Flux Removal
- Terminals, Plugs, and Jacks
III. Features & Benefits
- No Flash Point: Ensures safe application in a variety of environments.
- Non-flammable: Minimizes risk during use.
- Fast Evaporation: Reduces downtime associated with in-place cleaning methods.
- Residue-Free: Eliminates the need for rinsing or wiping, preventing harmful build-up.
- 360° Valve: Allows for easy application, even upside-down.
- CFC-Free: Environmentally friendly, contains no harmful CFC 113 or Methyl Chloroform.
IV. Physical Properties (Without Propellant)
- Flash Point: None
- Boiling Point: 30°C (Initial)
- Odor: Mild Ethereal
- Solubility: Slight in water
- Appearance: Colorless liquid
- % Volatile: 100%
- Vapor Density: 4
- Specific Gravity: 1.21 @ 20°C
- Dielectric Strength: 40,000 Volts per ASTM D-877
- Propellant: CO2
- Fire Point: None
V. Performance Characteristics
- ASTM D-1133 (Kauri-Butanol Value): 51
- ASTM D-877 (Dielectric Strength): 42,000 Volts
- Surface Tension: 18.5 Dynes/cm
- Evaporation Rate: Very Fast
- Residue: None
VI. Directions for Use
- Preparation: Always read the full label before use. Deactivate any equipment prior to application.
- Application: Spray liberally onto the surface and allow to run off. Use an extension tube for hard-to-reach areas.
- Caution: Avoid use on sensitive plastics like acrylic, ABS, Pebax 2533, and polystyrene. Test on a small area first.
- Post-Use: Ventilate the area and reactivate equipment only after ventilation is complete.
- For Lubricated Contacts: After cleaning, apply CRC 2.26 to restore lubrication.
VII. Disposal Considerations
Disposal methods vary depending on local regulations. Always dispose of both used and unused products in accordance with local, state, and federal regulations.
VIII. Special Use Warnings
Aerosol Cans:
- Do not puncture or incinerate.
- Avoid storage above 50°C and keep away from heat sources and direct sunlight.
- Caution: Aerosol cans conduct electricity; keep away from live electrical sources to avoid serious injury from flash fire or electrical shock.
General Safety:
- Use only in well-ventilated areas.
- Avoid inhalation of vapors and direct contact with skin or eyes.
- If ventilation is inadequate, use respiratory protection.
Contact our sales consultant in area:
Malaysia, Selangor (Klang, Puchong, Shah Alam, Subang), Kuala Lumpur (Sungai Buloh), Negeri Sembilan (Seremban), Melaka, Johor (Johor Bharu, Muar, Batu Pahat), Pahang (Temerloh, Kuantan), Kelantan (Kota Bahru), Terengganu (Kuala Terengganu), Perak (Ipoh), Kedah (Sungai Petani), Perlis, Penang (Bukit Mertajam, Butterworth, Seberang Prai), Sabah (Kota Kinabalu), Sarawak (Kuching), WP Putrajaya, WP Labuan, Indonesia, Singapore, Thailand, Philippines, Vietnam, Laos, Myanmar, Cambodia, Brunei
